![]() Presumably this gives the keys room to travel, despite the addition of the membrane-however, it also provides easier access to pry the caps off. The new keycaps measure in at around 1.25 mm in thickness, compared to the 1.5 mm thick keys in the 2017 model. We kept feeling like the caps were easier to remove and harder to ruin, and it turns out that they have been very slightly redesigned. The membrane in its present form covers more of the central area of the switch than Figure 5 shows, and does not “couple” to either the keycap or mechanism, but lies sandwiched between them. What we found is closer in spirit to Figure 5, wherein the keycap clips pass through the membrane to attach to the butterfly mechanism. Figure 2 in the patent lays out the layers we saw in our teardown, but showcases a secondary keycap layer not present in this design. This implementation lacks the “bellows” function intended to blow particulate away from the mechanism the gaps in the membrane are for keycap attachment, and to allow key presses without interference from an air cushion. No wonder Apple techs replace the whole assembly.Īpple’s patent application is pretty broad, basically taking ownership of any flexible barrier under a keyboard. Jeff makes this look easy, but this keyboard removal was hard-fought. That’s right-a single die-cut and molded sheet. When we’re finally able to peel the (absurdly thin) keyboard off of the aluminum case, we’re met with fields of clear silicone. Oh, and remove all 64 keycaps on the laptop. And even after the irreversible pin removal, we still need to cook the thing under a pile of iOpeners to loosen the adhesive holding it together. Apple could have saved themselves a lot of money, grief, and a ton of negative press if they just made this thing easier for their own techs to work on. And you wonder why Apple is replacing entire top case assemblies-including batteries-when they only really need to replace the keyboard. In order to get to the keyboard at all you need to gut the MacBook, peel off a large backing sticker, remove a whole brace of screws and bust through more than a dozen rivets. Now, that’s all well and good, but what does this silicone barrier actually look like? Are the keys wrapped in individual cushions? Did Apple just hide one of those goofy keyboard covers in this device? Like an ogre onion, this keyboard is a series of layers, so let’s get to peeling. And just like last time, a few poorly placed particles bring the mighty butterfly down to earth, never to click again.ĭust largely stays around the exterior of the new silicone shield, but particles can make their way past the barrier over time. Following the Mythbusters method of testing, we pushed the keyboard to failure with the higher-grit particulate we used last time: sand. Time will tell how long the barrier will hold up. On the 2018 keyboard, with the addition of more particulate and some aggressive typing, the dust eventually penetrates under the sheltered clips, and gets on top of the switch-so the ingress-proofing isn’t foolproof just yet. ![]() The previous-gen butterfly keys are far less protected, and are almost immediately flooded with our glowing granules. ![]() The holes in the membrane allow the keycap clips to pass through, but are covered by the cap itself, blocking dust ingress. Lo and behold, the dust is safely sequestered at the edges of the membrane, leaving the mechanism fairly sheltered. We started with a fine, powdered paint additive to add a bit of color and enable finer tracking (thanks for the tip, Dan!). We pumped this keyboard full of particulates to test our ingress-proofing theory. Since Apple informed their service providers that the membrane is “to prevent debris,” we’re inclined to think any change in noise level really is just a secondary feature. But hear me out-if Apple is advertising a quieter keyboard (without providing detail on how much quieter), shouldn’t the difference be immediately apparent to a first-time user? Why should we need high-grade equipment to prove what should be obvious to the ears? In a world where Apple once quietly introduced iPhone waterproofing without bragging about it, this seems like a strange instance of under-delivery. The result? We think the third-generation keyboard is slightly less clacky on the high-frequency end-which is admittedly kinda weak. We don’t have the snappiest equipment or an anechoic chamber lying around, so we resorted to a sound meter, a phone app, and our ears to compare current and past-gen keyboard noisiness. Testing, testingįirst off, I’ll tell you that we didn’t get conclusive noise level comparisons for this keyboard. ![]() If you’re not excited for a deep dive, check out our keyboard teardown for a more photo-driven experience. Just when we think we’ve exhausted one vein of tasty tech ore, we find something new. The 2018 MacBook Pro keyboard is a wealth of secrets-it just keeps surprising us.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |